Positioning the infrared heating panels is key

If you have purchased – or are about to purchase – infrared heaters, then understanding where to put them is important to get the best results.

Infrared heating panels don’t operate like conventional convection heating, which warms air. Instead the panels emit far-infrared radiation, which travels unimpeded until it hits a solid object, which will in turn absorb the infrared and then heat up. Do not mistake infrared with harmful UV light, which is on the other side of the light spectrum – infrared is 100% safe.

The main thing to remember is that if the infrared radiation is impeded before it reaches its destination, then the object will not warm up. As a result, to get the most out of the heating panel it should ideally be fitted in the centre of the room. Or if you have a larger area and are getting a number of panels, then they should be evenly distributed in that space. The panels should be above seating areas so as not to be shadowed, which is why positioning on the ceilings is by far the most popular.

The distribution of infrared heater rays

When the panel is positioned on the wall or ceiling, the infrared radiation will travel at 45o angles in all directions. If they are in a corner and too close to a wall other than the one they are attached to, then you will be warming a small concentrated area; this is not ideal since you will be wasting potentially useful heat. For this reason it is paramount that you don’t position the panels too close to the walls: rather ‘centre’ them as much as possible.

300Watt and 350Watt panels should be at least 0.5m (1.5 feet) or more from the floor – and the larger panels (basically anything over 600Watts) should be at least 1.5m (5 feet) away. When the panels are on they will beam the infrared radiation up to 3m(10 feet). If you have higher ceilings, please give us a ring and we can discuss appropriate models to use in this instance.

If you install the panels on the walls, then you should try and position them as high as possible. Positioning them too low will almost certainly result in furniture blocking the infrared radiation, which will limit their heating.

For the smaller panels we recommend having them at least 1.0m (over 3 feet) and for the bigger panels this to be positioned 1.4 mtr to center of panel. Like your radiators, the surface temperature of the panels gets to about 80oc, so do not touch or have objects too close to them.

The installation process

We recommend hardwiring them into an electric circuit where possible. This allows you to use a proper switch (like a light switch) to turn them on. It also means you can install a smart heating system for optimal efficiency. We strongly recommend a professional installation and having the panels ‘hard wired’ into your electrical system

In terms of the installations themselves we anticipate that most customers will seek the advice and expertise of a electrician who will hardwire the units to a thermostat and the property circuit board.

The infrared panels will invariably come with a frame on the back, which allows you to easily attach them to the wall. This does mean that the panels will sit about 1-2 cm off the wall.

Although the panels radiate heat from their front surface (which will get warm), the reflector technology will ensure that there is no heat being emitted out of the back. The fact they are sitting away from the wall also helps in this respect.

Most of the panels that are sold should be supplied with screws and fixings to get the panels attached to the wall or roof. We do recommend getting an electrician to fix them in position though, and hardwire them into your mains electricity rather than simply run through an existing plug socket.

When the panels are plugged in, they take about 90 seconds to get up to full heat intensity and since you don’t need to wait for the air to get warm, you should feel their effect very quickly. To stop the panels from overheating, they will modulate and come on and off as required; however we recommend having them installed with some form of thermostatic control to ensure the room doesn’t get too warm.  The most basic option is a timer plug adapter, however we recommend going for a proper thermostat and programmer unit if you have the funds available.

Installing infrared panels in the bathroom

Good infrared panels are either IP45 or IP54 rated, which means they can also be used in bathrooms.